The interesting thing about these XL systems is that even though they were smaller panels, zone-wise, they offered many features. Even the more basic versions had a list of functions and programming options you might expect to find on modern panels of today.
However, it offered several advanced features including:. The FBI security Omni line boosted the low zone and user code counts of the previous XL series, making them a better choice even for smaller applications. The Omni line picked up where the XL-series left off.
Omni systems offer more zones and user codes, along with the same list of other desirable features. It has 8 hardwired zones on board, but these can be expanded to 16 zones using zone doubling.
This means you actually get 16 zones without buying any expansion modules or other devices. By adding expansion equipment, the supports a maximum of 32 hardwired zones. Being a hybrid panel, the Omni supports up to 48 zones using wireless expansion. Aside from zone capabilities, the supports up to 64 user codes, 4 partitions, and 20 auxillary relays. Smaller FBI security panels in this line include the Omni 6-zones, expandable to 24 zones , and the Omni 4-zones, expandable to 8.
Maintenance of your system is normally taken care of by your alarm company, if you have one. If not, here is what's involved:. For help doing this, see my article on alarm system battery replacement. If you've lost your master code, or you've "inherited" an existing system and don't know the code, you have limited options. Panels in the XL-series have no easy way to recover just the master code; you have to factory default the whole panel.
This then requires the system to be re-programmed "from scratch", which can get tedious. Information on defaulting and programming can be found in the Installation Manual for your specific XL model. You can do this procedure yourself, but you may find it more worthwhile to have an alarm company do it for you.
When it comes to brushing your teeth and removing the masses of potentially cavity-causing bacteria known as plaque, there are two main types tools to choose from: a manual toothbrush or an electric one. While an electric toothbrush moves f. Prior to , all vehicles were manual transmission. Transmissions are necessary to transfer engine power to either the driveshaft or axle halfshafts and propel the vehicle. Manual transmissions are categorized into two basic types: slidin.
The keypad sounder annunciates differently to indicate the following conditions: CHIRP - Keypad sounds a short chirp to confirm each keystroke. When the switch is pushed toward the front of the keypad, in the opposite direction of the arrow , the switch is in the OFF position. Page Section 5. Once deleted their values will be null. Quick Arming allows arming the system without entry of a user code and will report as user NOTE: The system must be in ready mode.
A user code is required to disarm the system. On LED keypads the sounder will beep after each entry. The auto arm time represents the time of day that the area will automatically arm if it is not already armed. If selected, then a negative acknowledgment 4 short beeps will be heard after attempting to enter this mode. Upon entry to the system log view, LCD based keypads will show the events one at a time starting from the oldest event.
Proceed to question 02 through the sequence Next, enter the desired account number each digit followed by the key. This will be used by the CS downloading computer to determine the proper account information to download to this subscriber. Page Section 6. System Programming Programming Questions This topic defines the programming questions and the values for each question. NOTE: The checkmark highlights which options are selected. For Built-in Siren Driver, connect a single 8 ohm speaker only.
To select a trigger type enter the 2 digits in either L1 L2 or L3 L4 desired trigger type for each output trigger. Enter the digit from the table below.
Upon detection of the first violation, smoke detector power on conventional 4 wire smoke detectors connected to ZONE modules will be reset for a period of 8 seconds.
After this time period, power is restored. For a period of 5 seconds the fire zone will not be scanned allowing the smoke detectors to settle. The restore code will also be reported if the system is disarmed during an alarm.
This enables Fire and Burg zones to report restores. If a keypad tamper code is entered then it will be transmitted to the Central Station. Page Section 7.
0コメント