Click Create to start the deployment of Virtual Network Gateway. This deployment process will take more than 15 mins, so wait for the deployment to complete.
The above command will create a variable with the root certificate for the Client certificate that we are generating in the next step. Select the command as in the picture below and run it.
With the root certificate that we created in the previous step, we are using the root certicate variable that we have created and us the code below to generate a client certificate with the name P2SClient on the PowerShell ISE.
In the previous two steps, we have created a root certificate and client certificate using that root certificate. We are going to export the root certificate and the client certificate using the Microsoft Management Console MMC with the certificate snap-in. We are exporting Root certificate first and then client certificate subsequently. On the Root certificate export, we are not exporting a private key, select No, do not export the private key, and click Next.
Type the file path and file name with. Go to file path that we exported and right-click the root certificate, and select the Notepad in the open with apps selection. As the certificate content copied on the clipboard, open Azure Network gateway on the Azure portal and click configure now. Type an Address pool range, IKEv2, and SSTP as tunnel type, Azure as authentication type and type a name for root certificate name and paste the certificate content, which is there in the clipboard on the public certificate data box.
Next we are going to install the VPN client binary, right click the install file and select Run as administrator. We have created subnet gateway, deployed VPN gateway and connected windows 10 client and accessed the resource inside the Azure network with the private IP address of the device. If you have any questions or feed back, please post it in the comment column below. Your email address will not be published. Save my name, email, and website in this browser for the next time I comment.
As the validation passed, click Create to start the Virtual Network deployment. The newly created Gateway subnet will be listed on the subnet list with the name GatewaySubnet.
We have completed adding Gateway Subnet. Next, we are deploying Virtual Network Gateway. Once you have your cameras streaming back to your security video recorder, you can even do port forwarding and make your camera or NVR accessible for remote viewing from the outside world. Let's begin with the setup of configuring one IP Security Camera to wire into the Station and send the signal back to the 2.
A command prompt like the following will appear. Type ipconfig in the windows command prompt and press Enter. In our network, the router address is It is important to note that the default IP address for the AP and our ip cameras are as noted below. The AP and the Station radios both have the same default IP address before being configured, and will have to have a different IP address to be connected to the network at the same time.
For a router with IP address of XXX where XXX is the set of numbers that need to be changed and must be unique for each device on the network. For example, you can configure one camera and two radios as follows:. You may need to change the IP addresses of either one or both AP if there is an IP address conflict or they don't fit your network. You can follow instructions provided in How to view IP Cameras from a web browser on how to change the camera's IP address.
You can also find instructions on how to change the IP address of the access point here. To configure the AP you need to first connect it to your network so you can access it's internal web-based settings page. Each access point comes with a PoE injector. The default IP address of Ubiquiti radios is Be sure you are using a compatible network, and enter this IP address into the address bar of your web browser.
If you do not see the login page and get a security error message, follow the instructions provided in the image below. We are using Chrome as the browser in this case. The login page should look like the one below. The default username and password are ubnt and click on the checkbox on the bottom of the page before pressing login. After you log in for the first time you will be prompted to change the default password.
On the bottom right side, there will be an orange colored dialog box. Click on "System" there to navigate to the page to change your password. Once you are on the SYSTEM page, change the default password by clicking on the magnifying glass as pictured below to show a drop down section that lets you change the password.
Enter the old password and the new password on this page now. In addition, before saving changes set the Time Zone. To properly configure two wireless access points to communicate to each other, you have to configure one as an Access Point and the other as a Client Radio. First we will set the Access Point which will transmit the WiFi signal. Take a look at the image below to see how we have configured the radio. Make sure the Channel Width is set to 40 MHz. Otherwise, your settings will not be saved.
Which means you can only access them with another MIMO enabled access point or laptop. Since you are going to be using another identical AP to receive the signal, then, of course, you want to leave it on. Since we haven't defaulted the device first, let's check to make sure it's on. Let's proceed to configure the IP address.
Given that we have multiple radios that are by default on the same IP address, we have to change the ip address before connecting the next device or there will be a conflict trying to access on the default IP. We set our AP's ip address to Published Jan 29 AM Senior Member. Create Virtual Network Now we need to create new virtual network. Create Subnets Under the virtual network I am going to create a subnet for my servers.
To do that, Log in to Azure portal as global administrator Go to All Services and search for virtual network gateway. Once it is in list, click on it. Then we need to create client certificate. To export root certificate, Right click on root cert inside certificate mmc. Complete the wizard and save the cert in pc. To export client certificate, Use same method to export as root cert, but this time under private key page, select option to export private key.
In file format page, leave the default as following and click Next Define password for the pfx file and complete the wizard. Configure Point-to-Site Connection Next step of this configuration is to configure the point-to-site connection. Click on newly created VPN gateway connection. In this demo I will be using Linux and other mobile clients by default use IKEv2 to connect. For authentication type use Azure Certificates.
In same window there is place to define root certificate. Under root certificate name type the cert name and under public certificate data, paste the root certificate data you can open cert in notepad to get data.
Then click on Save to complete the process. Testing VPN connection Now we have finished with configuration. Log in to Azure portal from machine and go to VPN gateway config page. In my case I am using 64bit vpn client. After that, we can see new connection under windows 10 VPN page. Click on connect to VPN. Then it will open up this new window. Click on Connect in there. Then run ip config to verify ip allocation from VPN address pool.
In VPN gateway page also, I can see one connection is made. I have a server setup under new virtual network we created.
0コメント