Kirby diamond edition manual

This gives you the most efficient cleaning action. Lowering the Power Nozzle too far prevents proper cleaning and shortens belt life. You are now ready for portable power cleaning. To install the Portable Handle, see page It can also be used to clean the floors of cars. Use it to turn the Belt Lifter all the way to the left counter-clockwise until the red arrows line up.

If the Ultimate G will not operate, see page 51, question 2, items 4 and 5. It is an excellent tool to apply many different types of water-based liquids to any type of surface. The spray can be adjusted ranging from very fine to coarse. Before reinstalling the jar, make sure the portable sprayer dip tube is attached to the spray gun body. Always squeeze the trigger fully to permit maximum flow.

A stream of suds will come out of the cap. The suds can be sprayed directly onto the surface being cleaned or on a plain paper bag or in a bowl and then applied to the surface being cleaned.

By using the L-shaped handle, turn the Carpet Shampoo System Nozzle Belt Lifter to the right clock- wise until the green arrows line up. Page 32 not hot. Do not use more, as over-foaming will result. NOTE: One tankful of solution will clean about a 10x12 foot carpet 3x3. Some moisture will accumulate in the front of the tray. The brush will snap out and the belt can be replaced.

Be certain the belt is placed in the center of the brush. However, buff immediately, avoiding any 3. For best results, apply a very thin coat of Kirby drying time. Miracle Wax using the roller applicator. It is not Once you have completed the steps above, the floor Begin waxing according to the directions in box on previous page.

Turn the Accessory Lock all the way to the right clockwise to lock the nozzle in place. Page 41 Make sure the green arrows line up for stor- age see page 10 for discussion of the Belt Lifter. Before fluffing the carpet, raise the nozzle all the way up by pushing the Toe-Touch Control Bottom Pedal all the way down.

Place the cleaner on the carpet to be fluffed. The instant the brush contacts the carpet, stop lowering the brush. Use fine paper for a smooth finish and coarse paper to clear rough surfaces or remove paint. Slide the sheet into the front clamp and lock the clamp lever. The Turbo Accessory now becomes a polisher. Use it for polishing hard waxed surfaces, such as table tops, paneling, large flat surfaces and cars.

When pressing the release button, avoid placing pressure on the outer ring brush. As with most modern appliances, it requires a modest degree of routine maintenance to keep it operating efficiently. To change the belt, remove the nozzle from the Ultimate G as on page Handle Fork Back Screw. Swivel Cord Hook. Cord Hook Swivel Screw. Cord Hook Swivel Spring. Handle Grip Assembly. Rear Cover Assembly. Handle Grip Bag Release Button.

Belt Lifter Label. Belt Lifter Screw. Belt Lifter Body Assembly. Belt Lifter Flat Washer. Spring Washer for Belt Lifter. Label Belt Lifter Instructions 5 Pack. Label for Brush Adjustment 5 Pack. Belt Lifter Bearing. Belt Lifter Hook. Rug Plate Latch Assembly. Rivet Latch Assembly. Nozzle Bumper. Brush Roll Assembly. Brush End Cap Small. Brush End Cap Large.

Knurled Brush Roll Belt. Sleeve Rug Plate Latch. Brush Performance Indicator Assembly. Spring Washer. Bare Floor Duster Pad. Miracle Waxer Handle Assembly. Miracle Waxer Roller English. Rear Wheel Hubcap. Rear Wheel Clip. Primary Drive Belt. Rear Axle Bushing. Right Axle Retainer. Left Axle Retainer. Axle Retainer Screw. Rear Axle Spring. Neutral Drive Pedal Screw.

Rear Axle Bearing. Neutral Drive Pedal Assembly. Clutch Overload Gear Assembly. Rear Axle Ball Retainer. Rear Axle Ball. Drive System Base Pan Screw.

Headlight Cap Casting. Lens Headlight Cap. Light Bulb 8 Watt. Headlight Frame Bracket. Headlight Pivot to Slide Bracket Screw. Headlight Pivot Casting. Headlight Pivot Bushing. Headlight Pivot Plate. Plate to Headlight Pivot Screw. Slide Bracket Casting. Wedge Slide Adjustment. Guide Block Slide Bracket. Guide Block Slide Screw. Roller Bearing Assembly. Slide With Centering Spring Assembly. Insulation Tube.

Light Wire With Socket. Insulator Sleeve Black. Nov 23, This manual is written for use with the Kirby Model Gsix. We at Kirby sincerely hope this Owner's Manual will help you obtain years of satisfactory performance All manuals and maintenance tips for Kirby vacuum cleaners and repair manuals for Kirby model vacuums are authored by GoodVac.

This is online Kirby vacuum manual by Goodvac. View and Download Kirby G Series owner's manual online. G Series Vacuum Cleaner pdf manual download. Join Co-production practitioners network. Sign Up or Sign In.